Tubbutec Midi USB bridge A

[tubbutec]

Questions and FAQ about Midi USB bridge A
https://tubbutec.de/usb-bridge-a/

If you can confirm compatibility with a device, please let us know and we will update the list.

KEYBOARDS / CONTROLLER

Korg Nanokontrol 2, Korg Nanokey 2
Korg microKEY 37 MkII
Roger Linn Design – Linnstrument
AKAI Professional LPK 25
Alesis Q49
Axis 49

SYNTHESIZERS / SEQUENCERS

Korg SQ-1
Novation Launchpad Mini MK2
Novation Peak
Teenage Engineering OP-1
Arturia Beatstep Pro

USB MIDI INTERFACES

Roland UM1-G
Thomann Midi USB 1×1
RME Fireface UFX
Tubbutec µTune

[pmarchitect]

Hi, does this work with the Launchpad Mini Mk3??

[Paranormal Patroler]

Works with Axis 49

[Jahmontee]

Does anybody know if this will work with a midi fighter and/or the midi fighter twist…. Preferably both at the same time.

[SLOfizz]

Why does this not work with my iPad or Mac? Droid?

Why isn’t there a TRS type b or a dip switch on the back to convert. This literally only works with my Keystep.

[_ttc_]

Are there pins on the back of the module to connect MIDI output directly to expert sleepers modules (via pins on back of the modules)? If possible I’d like to avoid needing the MIDI break out box for my FH-2 and ES-9.

[SLOfizz]

Nope. No pins on back. I just drilled a TRS jack into the case and wired that to my expert sleepers. You don’t need the tiny expander if you can solder a Jumper cable to a TRS jack.

[_ttc_]

Appreciate the info. Thanks!

[tubbutec]

Are there pins on the back of the module to connect MIDI output directly to expert sleepers modules (via pins on back of the modules)? If possible I’d like to avoid needing the MIDI break out box for my FH-2 and ES-9.

There is in fact a pin on the back. It has a copy of the TRS midi output. With a wire it can be connected to other modules.

[Rrobosyn]

Any info on if/when this module might be available again? Thanks!

[SLOfizz]

Are there pins on the back of the module to connect MIDI output directly to expert sleepers modules (via pins on back of the modules)? If possible I’d like to avoid needing the MIDI break out box for my FH-2 and ES-9.

There is in fact a pin on the back. It has a copy of the TRS midi output. With a wire it can be connected to other modules.

Where? There is only a jumper for the 12v 5V select, unless you mean to solder onto your board…. I could solder on to anyones jack.

[tubbutec]

Any info on if/when this module might be available again? Thanks!

we are in production, 1-2 weeks.

[tubbutec]

Are there pins on the back of the module to connect MIDI output directly to expert sleepers modules (via pins on back of the modules)? If possible I’d like to avoid needing the MIDI break out box for my FH-2 and ES-9.

There is in fact a pin on the back. It has a copy of the TRS midi output. With a wire it can be connected to other modules.

Where? There is only a jumper for the 12v 5V select, unless you mean to solder onto your board…. I could solder on to anyones jack.

You might have the rev1 version that does not have this. On newer versions there is a solder point for a pin, signal already conditioned to work alongside the TRS output. The pin sits below the TRS jack on the bottom. This is not an advertised feature, we usually solder the pin on request.